3- 5 days delivery
Product name：10K Standard Plus Resin
Model number：10K-10A (High Clear)
Applicable industrial： Suitable for the jewellery industry, dentistry, teaching and research, toy design, handicraft design, industrial parts design, etc.
 
Product Advantages
The curing time is short, the finished product surface is smooth, the precision is high, the detail performance is good, and the outline is clear.
The printed product has a certain toughness.
Product Technical Parameters before Curing
Viscosity: 300~500mPa·s (NDJ-8S rotary rheometer（25℃）)
Density: 1.05~1.25g/cm3 (densitometer(25℃))
Principle of 3D Printing
UV-curable additive manufacturing resin cures create 3D printed objects by curing the UV-curable additive manufacturing resin layer by layer using a high-resolution UV projector. Molding process: The LCD/DLP printers contain a resin tank that can hold the resin and resin storage, the LCD/DLP imaging system is placed below the tank and its imaging surface is located at the bottom of the tank. By energy and graphic control, a thin layer of resin (50μm/25μm) of a certain thickness and shape can be cured each time (this layer of resin is exactly the same as the section obtained from the previous section). A lifting mechanism is set above the liquid tank to lift up a certain height (the height is consistent with the layer thickness) after each cross-section exposure so that the solid resin currently cured is separated from the bottom surface of the liquid tank and bonded to the lifting plate or the resin layer formed last time. In this way, three-dimensional entities are generated through layer-by-layer exposure and lifting, and finally, the transparent resin-cured product after curing and moulding is obtained.
 
Recommended Print Parameters
Recommended printing time: Bottom exposure time 25-35s, layer exposure time 2.5s-3.5s. (6.6 inch black and white screen, light intensity 3500~4500µw/㎝²)
Bottom Lift Distance: 6mm
Lifting Distance: 6mm 
Bottom Lift Speed: 60mm/min
Lifting Speed: 80mm/min
Retract Speed: 150mm/min
Wavelength: 385~410nm
Molding Test Requirements and Technical Parameters after Molding      
Molding Test Environment and Standard:
①Temperature: 23±2℃
②Relative humidity: 50%RH±5%RH
③The standard of the test piece: ASTM
④Post curing condition: The test piece was placed in water under 405nm ultraviolet radiation of 200mw/cm² for one minute.
Technical Parameters after Molding:
1、Maximum force(KGF):165.7±10% 
2、Tensile strength(MPa): 39.06±10%
3、Deformation of maximum point of force(mm): 5.32±10%
4、Elongation at yield point(%): 5.71±10%
5、Elongation at break(%):9.4±10%
6、Maximum bending strength(MPa): 48.93±10%
7、Flexural modulus(MPa):1412.8±10%
8、Hardness(Shore D)：80-86
9、Impact strength(j/m):80±10%
10、Tensile modulus：538.41±10%
 
Warning
This product is disposable and cannot be reused.
This product should not be in contact with eyes, skin or clothing, and should not be tasted or eaten. Use only in good ventilation, please pay attention to air circulation, and take protective measures. Clean thoroughly after operation.
This product is liquid and has a slight odor. Please wear a mask when using it to avoid inhalation of aerosol and infection.
4. This product should be stored in an airtight container, sealed immediately after use, and placed in a dry and well-ventilated place without exposure to sunlight.
5. In case of accidental inhalation of this product, leave the scene in time, quickly transfer to a place with fresh air, in case of adverse reactions, go to the hospital for treatment in time.
6. If swallowed this product accidentally, do not induce vomiting, keep a state of rest, timely sent to the hospital treatment.
7. In case of contact with skin, wash skin thoroughly with soapy water or seek medical advice.
8. In case of contact with eyes, open eyelids immediately, rinse with soapy water for about 20 minutes and seek medical advice immediately.
9. Waste water/waste shall be disposed of in accordance with local environmental regulations.
 
Storage:
Please seal the product and store it in a dry, well-ventilated room with no corrosive gas, keep away from heat source, keep away from moisture and avoid sun exposure. 
Shelf life 2 year. (The product is best stored at 25~30℃)